Section 401 (Anti-Lock Control System)
WARNING: This page is about a different car, the 2004 Mercury Mountaineer and 2004 Ford Explorer. However, it is still accessible from the selected car via links, so may be relevant.
- Specifications
- Description And Operation
- Anti-Lock Control
- Anti-Lock Brake System (ABS)
- Anti-Lock Brake System (ABS) With Stability Assist
- principles of Operation
- Anti-Lock Brake System
- Electronic Brake Distribution (EBD)
- Panic Assist Braking (ABS With Stability Assist)
- Stability Assist
- Sensor Cluster (ABS With Stability Assist)
- Steering Wheel Rotation Sensor (ABS With Stability Assist)
- Active Brake Booster (ABS With Stability Assist)
- ABS Module Configuration
- ABS Module Calibration (ABS With Stability Assist)
- Anti-Lock Control
- Diagnosis And Testing
- Anti-Lock Control
- Notes
- Special Tool(s)
- Inspection and Verification
- Symptom Chart
- Connector Circuit Reference Table
- Anti-Lock Brake System (ABS) C155
- Sensor Cluster C3179 (2WD)
- Sensor Cluster C3180 (4WD)
- Steering Wheel Rotation Sensor C226
- Active Brake Booster C149
- Primary Brake Pressure Transducer C147
- Brake Pedal Travel Sensor C148
- Stability Assist Switch C280
- LH Front Wheel Speed Sensor C150, RH Front Wheel Speed Sensor C160, LH Rear Wheel Speed Sensor C440, RH Rear Wheel Speed Sensor C426
- Rear Wheel Speed Sensor C455
- Speed Control Deactivator Switch C1025
- Pinpoint Tests
- Pinpoint Test A: No Communication With The Abs Module
- Pinpoint Test A: No Communication With the ABS Module
- Pinpoint Test B: DTC B1483 - Brake Pedal Input Signal Failure
- Pinpoint Test C: DTC B1676 - Battery Pack Voltage Out Of Range
- Pinpoint Test D: DTC C1095 - Abs Hydraulic Pump Motor Circuit Failure
- Pinpoint Test D: DTC C1095 - ABS Hydraulic Pump Motor Circuit Failure
- Pinpoint Test E: DTC C1145, DTC C1155, DTC C1165, DTC C1175 - Wheel Speed Sensor Input Circuit Failure
- Pinpoint Test F: DTC C1233, DTC C1234, DTC C1235, DTC C1236 - Wheel Speed Sensor Input Signal Missing
- Pinpoint Test F: DTC C1233, DTC C1234, DTC C1235, DTC C1236- Wheel Speed Sensor Input Signal Missing
- Pinpoint Test G: DTC C1277 and C1278 - Steering Wheel Angle 1 and 2 Circuit Failure/Faulted
- Pinpoint Test G: DTC C1277 And C1278- Steering Wheel Angle 1 And 2 Circuit Failure/Faulted
- Pinpoint Test H: DTC C1279, C1280, C1281, C1282, C2769, C2770 - Sensor Cluster Fault
- Pinpoint Test H: DTC C1279, C1280, C1281, C1282, C2769, C2770 -Sensor Cluster Fault
- Pinpoint Test I: DTC C1285 - Booster Solenoid Circuit Failure
- Pinpoint Test I: DTC C1285- Booster Solenoid Circuit Failure
- Pinpoint Test J: DTC C1287 - Brake Booster Pedal Force Switch Circuit Failure
- Pinpoint Test K: DTC C1288 And C1440 (Abs With Stability Assist) - Brake Pressure Transducer Input Circuit Failure
- Pinpoint Test K: DTC C1288 and C1440 (ABS With Stability Assist) - Brake Pressure Transducer Input Circuit Failure
- Pinpoint Test L: DTC C1730 - Reference Voltage Out Of Range (+5 V)
- Pinpoint Test M: DTC C1960 - Driver Brake Apply Circuit Fault
- Pinpoint Test N: DTC B2734, B2736, B2737, B2738, B2740 - Pedal Travel Sensor Fault
- Pinpoint Test O: Stability Assist Cannot Be Disabled
- Pinpoint Test O: The Stability Assist Cannot Be Disabled
- Pinpoint Test P: DTC C1440 (Abs Only) - Pressure Transducer Signal Fault
- Pinpoint Test P: DTC C1440 (ABS Only) - Pressure Transducer Signal Fault
- Pinpoint Test Q: DTC C1998 - Module Calibration Not Complete
- Pinpoint Test R: The Stability Assist Switch Indicator Is Never/Always On
- Anti-Lock Control
- Removal And Installation