Automatic Transaxle System
- General
- Automatic Transaxle System
- Troubleshooting (A/T)
- Diagnosis Function
- Torque Converter Stall Test
- Torque Converter Stall Test Judgement Results
- Hydraulic Pressure Test
- Basic Inspection Adjustment
- Inspection Procedures For Diagnostic Trouble Codes
- DTC P0712 & P0713: Short To Ground, Open Or Short To Battery
- DTC P0715: Input Shaft Speed Sensor Open, Short To Battery Or Short To Ground
- DTC P0720: Output Shaft Speed Sensor Open, Short To Battery Or Short To Ground
- DTC P0703: Stop Switch Short Circuit
- DTC P0750: Low & Reverse Solenoid Valve Open Or Shorted
- DTC P0755: Under Drive Solenoid Valve Open Or Shorted
- DTC P0760: Second (2nd) Solenoid Valve Open Or Shorted
- DTC P0765: Overdrive (OD) Solenoid Valve Open Or Shorted
- DTC P0743: Damper Clutch Control (DCC) Solenoid Valve Open Or Shorted
- DTC P0731: 1st Gear Asynchronous Error
- DTC P0732: 2nd Gear Asynchronous Error
- DTC P0733: 3rd Gear Asynchronous Error
- DTC P0734: 4th Gear Asynchronous Error
- DTC P0736: Reverse Asynchronous Error
- DTC P1604: CAN (No ID Form ECU)
- DTC 1603: CAN (Communication BUS Off)
- DTC P0741: Damper Clutch Abnormal System
- DTC P0742: Damper Clutch Stuck On
- DTC P1723: A/T Control Relay Shorted To Ground Or Open
- Notes
- Description
- DTC Detecting Condition
- Schematic Diagram
- Inspection Procedures
- 1. Check The DTC Of The A/T Control Relay
- 2. Check The A/T Control Relay Connector
- 3. Check The A/T Control Relay Continuity
- 4. Check The A/T Control Relay Harness
- 5. Check The A/T Control Relay Harness
- 6. Use the Hi-Scan Pro to delete P1723 from memory in the PCM. Test drive the vehicle for two key-on the key-off driving cycles.
- 7. Replace The PCM
- DTC P0707 & P0708: Transaxle Range (TR) Switch Short To Ground, Open Or Shorted Between Switches
- Inspection Process For Trouble Symptoms
- Inspection Procedure 1
- Inspection Procedure 2
- Inspection Procedure 3
- Inspection Procedure 4
- Inspection Procedure 5
- Inspection Procedure 6
- Inspection Procedure 7
- Inspection Procedure 8
- Notes
- 1. The Actuator Test Of The Low-Reverse Solenoid Valve
- 2. When Does The Shock Occur?
- 3. Hydraulic Pressure Test
- 4. Check The Reverse Clutch System & Low-Reverse Brake System
- 5. Check The Reverse Clutch & Low-Reverse Brake
- 6. Shock Sometimes Occur
- 7. Check The Scan Tool Data
- 8. The Valve Body Cleaning (Valve Body Disassembly, Cleaning & Reassembly
- Inspection Procedure 9
- Inspection Procedure 10
- Notes
- 1. The Actuator Test Of The Low-Reverse Solenoid Valve, Underdrive Solenoid Valve, Second Solenoid Valve, Overdrive Solenoid Valve
- 2. Adjust The Line Pressure
- 3. Check The Clutch & The Brake
- 4. Replace The Oil Pump Assembly (The Oil Pump Cannot Be Disassembled)
- 5. The Valve Body Cleaning (Valve Body Disassembly, Cleaning & Reassembly)
- Inspection Procedure 11
- Notes
- 1. Check The Scan Tool Data Of The Output Shaft Speed Sensor
- 2. Check The Scan Tool Data Of The Throttle Position Sensor
- 3. Check The Scan Tool Data Of The Solenoid Valve
- 4. Adjust The Line Pressure
- 5. The Valve Body Cleaning (Valve Body Disassembly, Cleaning & Reassembly)
- 6. Replace The Solenoid Valve
- Inspection Procedure 12
- Inspection Procedure 13
- Inspection Procedure 14
- Inspection Procedure 15
- Automatic Transaxle
- Automatic Transaxle Shift Control