Mixture Formation - 246 Chassis

• General Information
  • Mixture formation - AH07.00-Z-9999AZ
• Basic Knowledge
  • Table of contents for function description of gasoline injection and ignition system with direct injection - GF07.70-P-0998MT
  • Overview of system components for gasoline injection and ignition system with direct injection - GF07.70-P-9998MT
• Safety Precautions
  • Safety information: Mixture formation - AS07.00-Z-9999ZZ
• Testing & Repair
  • Exhaust emission test I - AR07.00-P-1000A
  • Remove/install high-pressure pump - AR07.02-P-1020MT
  • Remove/install fuel injectors - AR07.03-P-0004MT
  • Remove/install rail - AR07.03-P-1010MT
  • Remove/install a pressure sensor - AR07.04-P-0050MT
  • Remove/install injection system control unit - AR07.08-P-7008MT
  • Remove/install pressure transducer for boost pressure control - AR07.17-P-7002MT
  • Remove/install heated O2 sensor - AR07.52-P-5303MT
  • Remove/install throttle valve actuator - AR07.61-P-1401MT
• Test & Adjustment Values
  • Test and adjustment values: Passenger cars: Mixture formation - BE07.00-Z-9999AZ
• Torque Specifications
  • Tightening torques: Passenger cars: Mixture formation - BA07.00-Z-9999AZ
• Wiring Diagrams
  • Wiring diagram for gasoline direct injection system control unit
    • Wiring diagram for gasoline direct injection system control unit - PE07.08-P-2101IAA
    • Wiring diagram for gasoline direct injection system control unit - PE07.08-P-2101IAC
  • Electrical function schematic, ignition ON - PE07.10-P-2700IAC
  • Electrical function schematic for starting - PE07.10-P-2701IAC
  • Electrical function diagram for ignition OFF - PE07.10-P-2702IAC
  • Electrical function schematic for fuel supply - PE07.10-P-2703IAC
  • Electrical function diagram for injection control - PE07.10-P-2704IAC
  • Electrical function schematic for ignition system - PE07.10-P-2705IAC
  • Electrical function schematic, synchronization of the injection and firing order - PE07.10-P-2706IAC
  • Electrical function schematic for start phase, post-start phase and warm-up enrichment - PE07.10-P-2707IAC
  • Electrical function schematic for rpm control - PE07.10-P-2708IAC
  • Electrical function schematic, alternator interface - PE07.10-P-2709IAC
  • Electrical function schematic for lambda control - PE07.10-P-2710IAC
  • Electrical function schematic for smooth running control - PE07.10-P-2711IAC
  • Electrical function schematic for thermal management - PE07.10-P-2712IAC
  • Electrical function schematic for torque coordination - PE07.10-P-2713IAC
  • Electrical function schematic for deceleration fuel shutoff - PE07.10-P-2714IAC
  • Electrical function schematic for knock control - PE07.10-P-2715IAC
  • Electrical function schematic for camshaft adjustment - PE07.10-P-2716IAC
  • Electrical function schematic for engine limp-home mode - PE07.10-P-2719IAC
  • Electrical function schematic for on-board diagnosis - PE07.10-P-2720IAC
  • Electrical function schematic for engine timing start stop - PE07.10-P-2722IAC
  • Electrical function schematic for safety fuel shutoff - PE07.10-P-2733IAC
• Special Tools
  • 000 589 68 03 00 Box wrench bit - WS07.00-N-0004A
  • 103 589 00 21 00 Testing unit - WS07.00-N-0014B
  • 000 589 00 68 00 Cleaning kit - WS07.00-P-0001C
  • 000 589 68 03 00 Box wrench bit - WS07.00-P-0004B
  • 270 589 01 68 00 Cylinder brush - WS07.00-P-0063B
  • 000 589 69 03 00 Ring wrench bit - WS07.00-P-0088B
  • 272 589 00 43 00 Assembly tool - WS07.00-P-0127B
  • 278 589 00 15 00 Drift - WS07.00-P-0152B
  • 278 589 00 33 00 Puller - WS07.00-P-0153B
  • 278 589 01 15 00 Drift - WS07.00-P-0154B