Transmission - Removal, Replacement And Installation
- Automatic Transmission (Aw55-50/51SN; 2001-2004)
- Oil, changing
- Replacing gear selector knob
- Replacing lock function
- Replacing the cable harness for the control system
- Replacing the carrier plate
- Replacing the engine speed (RPM) sensor
- Replacing the gear selector lever and/or indicator panel with boot
- Replacing the gear-shift position sensor
- Replacing the key lock cable
- Replacing the panel with integrated winter mode switch
- Replacing the right and left-hand differential seals
- Replacing the sealing ring for the gear shift linkage rod
- Replacing the sealing ring for the oil pump
- Replacing the solenoids and control system
- Replacing the speed sensor
- Replacing the transmission
- Replacing
- Notes
- Removal
- Introduction
- Removing engine compartment components
- Detaching engine compartment components
- Detaching transmission connectors
- Installing the lifting device
- Removing the heat deflector plate and member
- Detaching the left-hand side drive shaft
- Detaching the right-hand side drive shaft
- Detaching oil pipes
- Removing the screws from the torque converter
- Connecting fixture
- Removing the engine, transmission and starter motor screws
- Removing the engine mounting
- Removing the screws, engine/transmission
- Removing the transmission
- Installation
- Cleaning and checking
- Installation
- Installing the transmission
- Lifting engine and transmission
- Installing the screws, transmission/engine
- Fitting the torque converter screws.
- Installing the front and rear brackets
- Installing left/right drive shafts
- Installing the support member
- Installing the oil pipes
- Installation, Cont.
- Installing the shift cable
- Adjusting the gear cable
- Installing other components
- Finishing
- Replacing
- Shift cable, replacing
- Shift lock and ignition switch interlock
- Changing Oil (Aw50-42; 2000)
- Gear Selector Assembly (Aw55-50/51SN; 2001-2004)
- Replacing Components In The Passenger Compartment (Aw50-42; 2000)
- Replacing Components In Transmission (Aw50-42; 2000)
- Inspecting / replacing the cable harness for the solenoids
- Notes
- Preparations
- Preparations, continued
- Opening the control system
- Disconnecting connections
- Checking the cable harness
- Removing the gear-shift position sensor
- Removing the cable harness
- Connecting the cable harness to the control system
- Installing the cover
- Connecting the cable harness
- Installing / adjusting the gear position sensor
- Installing components
- Installation
- Replacing accumulator pistons/sealing rings B2/C2
- Replacing accumulator pistons/sealing rings C3
- Replacing control system
- Replacing left-hand side drive shaft seal
- Replacing oil temperature sensor
- Replacing right-hand side drive shaft seal
- Notes
- Installing lifting beam
- Preparations
- Remove cover
- Disconnecting drive shaft
- Removing components
- Removing drive shaft from transmission
- Removing sealing ring
- Installing sealing ring
- Installing drive shaft
- Install cover
- Installing longitudinal member
- Installing stub axle, brake hose and ABS line
- Installing splash guards and wheel
- Replacing the engine speed (RPM) sensor
- Replacing the gear-shift position sensor
- Replacing the sealing ring for the gear shift linkage rod
- Replacing the speed sensor
- Replacing torque converter/oil pump sealing ring
- Solenoids, inspection/replacement
- Inspecting / replacing the cable harness for the solenoids
- Replacing Other Components In The Engine Compartment (Aw50-42; 2000)
- Replacing The Shift Lock Solenoid And Micro-Switch (Aw55-50/51SN; 2001-2004)
- Replacing The Transmission Control Module (TCM) (Aw55-50/51SN; 2001-2004)
- Replacing Transmission (Aw50-42; 2000)
- Replacing the transmission
- Replacing
- Notes
- Removing
- Introduction
- Remove the engine compartment components
- Disconnect the hose from the charge air cooler (CAC) at the intake manifold
- Disconnecting the transmission connectors
- Removing the screws joining the transmission, the engine and the starter motor
- Remove the Poly V-belt
- Installing hoist
- Removing the front wheel and splash guards
- Removing the components on the left and right-hand sides:
- Disconnecting the drive shaft, left-hand side
- Remove the hose and the clamp
- Removing, left-hand side:
- Remove the longitudinal beam
- Remove the cross stay member
- Removing on the right-hand side
- Remove the AC compressor
- Disconnecting the oil pipes
- Removing the torque converter screws
- Lowering the engine
- Connecting the fixture
- Removing the engine-transmission screws
- Removing the transmission
- Cleaning and inspection
- Installing
- Notes
- Installing the transmission
- Lifting the engine and transmission
- Installing the transmission-engine screws
- Installing the torque converter screws
- Installing the front and rear brackets
- Install the AC compressor
- Installing left/right drive shafts
- Checking the drive shafts
- Install the hose to the charge air cooler (CAC)/charge air pipe
- Installing the longitudinal beam
- Install the stay for the front cross member
- Installing the oil pipes
- Tightening the stub axle/installing the ABS and brake lines
- Installing the splash guards and wheels
- Installing, continued
- Installing the gear selector cable
- Install and tighten the hose clamp and the charge air pipe securing the clamp
- Install the Poly V-belt
- Install the engine compartment components
- Finishing
- Installing the engine with the transmission
- Removing the engine with the transmission
- Replacing
- Replacing the transmission
- Test Drive Form, Description (Aw55-50/51SN; 2001-2004)