Specifications Index
(OPTRA) SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | Automatic FASTENER TIGHTENING SPECIFICATIONS Manual FASTENER TIGHTENING SPECIFICATIONS |
||
| Axle Nut/Hub Nut | |||
| Front | 221 lb ft (300 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc/Drum Brakes | |||
| Service Specifications | BRAKE SYSTEM SPECIFICATIONS Link | ||
| Torque | Disc FASTENER TIGHTENING SPECIFICATIONS Drum FASTENER TIGHTENING SPECIFICATIONS |
||
| Charging | |||
| Generator | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine drive belts are not adjustable | ||
| Drive Belt Routing | See illustration under POWER STEERING PUMP DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | N/A | ||
| Radiator Cap Pressure | Specification is stamped on pressure cap | ||
| Thermostat R & I | THERMOSTAT REPLACEMENT (1.4L/1.6L) THERMOSTAT REPLACEMENT (1.8L/2.0L) |
||
| Water Pump R & I | COOLANT PUMP REPLACEMENT | ||
| Engine Mechanical | |||
| Compression | 1.4L ENGINE COMPRESSION TEST 1.6L ENGINE COMPRESSION TEST 1.8L (L79) ENGINE COMPRESSION TEST 1.8L (LDA) ENGINE COMPRESSION TEST 2.0L ENGINE COMPRESSION TEST |
||
| Oil Pressure | 1.4L minimum oil pressure at idle should be 250 kPa (35 psi) 1.6L minimum oil pressure should be 30 kPa (8.88 psi) 1.8L (L79) minimum oil pressure at idle should be 250 kPa (35 psi) 1.8L (LDA) minimum oil pressure at idle should be 250 kPa (35 psi) 2.0L minimum oil pressure should be 30 kPa (8.88 psi) |
||
| Overhaul | 1.4L ENGINE MECHANICAL SPECIFICATIONS 1.6L ENGINE MECHANICAL SPECIFICATIONS 1.8L (L79) ENGINE MECHANICAL SPECIFICATIONS 1.8L (LDA) ENGINE MECHANICAL SPECIFICATIONS 2.0L ENGINE MECHANICAL SPECIFICATIONS |
||
| Torque | 1.4L FASTENER TIGHTENING SPECIFICATIONS 1.6L FASTENER TIGHTENING SPECIFICATIONS 1.8L (L79) FASTENER TIGHTENING SPECIFICATIONS 1.8L (LDA) FASTENER TIGHTENING SPECIFICATIONS 2.0L FASTENER TIGHTENING SPECIFICATIONS |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 1.4L 25 lb ft +30°+15° (35 N.m +30°+15°) 1.6L 25 lb ft +30°+15° (35 N.m +30°+15°) 1.8L (L79) 48 lb ft + 30° + 15° (65 N.m + 30° + 15°) 1.8L (LDA) 25 lb ft +30°+15° (35 N.m +30°+15°) 2.0L 48 lb ft + 30° + 15° (65 N.m + 30° + 15°) |
||
| Fuel System | |||
| Pressure Specification | 1.4L 55-62 psi (380-427 kPa) 1.6L 38-44 psi (262-303 kPa) 1.8L (L79) 55-62 psi (380-427 kPa) 1.8L (LDA) 55-62 psi (380-427 kPa) 2.0L 55-62 psi (380-427 kPa) |
||
| Fuel Pressure Test Procedure | 1.4L CIRCUIT/SYSTEM VERIFICATION 1.6L CIRCUIT/SYSTEM VERIFICATION 1.8L (L79) CIRCUIT/SYSTEM VERIFICATION 1.8L (LDA) CIRCUIT/SYSTEM VERIFICATION 2.0L CIRCUIT/SYSTEM VERIFICATION |
||
| Fuel Filter Location | 1.4L In-line filter locted under vehicle along side rail. See R&I Procedure 1.6L In-line filter locted under vehicle along side rail. See R&I Procedure 1.8L (L79) In-line filter locted under vehicle along side rail. See R&I Procedure 1.8L (LDA) In-line filter locted under vehicle along side rail. See R&I Procedure 2.0L Fuel filter is assembled to the fuel pump and is replaced as an assembly |
||
| Fuel Filter R & I | 1.4L FUEL FILTER REPLACEMENT 1.6L FUEL FILTER REPLACEMENT 1.8L (L79) FUEL FILTER REPLACEMENT 1.8L (LDA) FUEL FILTER REPLACEMENT 2.0L FUEL PUMP REPLACEMENT |
||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| ??? | 1-3-4-2 | ||
| Ignition Wires (Resistance) | 1.4L/1.6L/2.0L 2000-12,000 Ohms 1.6L/1.8L 1000 Ohms per foot |
||
| Ignition Wires (Routing) | |||
| 1.4L | N/A | ||
| 1.6L | See illustration under SPARK PLUG WIRE REPLACEMENT | ||
| 1.8L (L79) | See illustration under SPARK PLUG WIRE REPLACEMENT | ||
| 1.8L (LDA) | N/A | ||
| 2.0L | See illustration under SPARK PLUG WIRE REPLACEMENT | ||
| Spark Plug | |||
| 1.4L/1.6L (Type Woojin - BKR6E-11) | |||
| Gap | 0.039-0.043 in (1.0-1.1 mm) | ||
| Torque | 18 ft lb (25 N.m) | ||
| 1.8L (Type NGK - BKUR6ETB) | |||
| Gap | 0.028-0.035 in (0.7-0.9 mm) | ||
| Torque | 18 ft lb (25 N.m) | ||
| 2.0L (Type Bosch - FLR8LDCU) | |||
| Gap | 0.039 in (1.0 mm) | ||
| Torque | 18 ft lb (25 N.m) | ||
| Starting | |||
| Starter | STARTER MOTOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 74 ft lb (100 N.m) | ||