Engine Mechanical / Engine Control System - Service, Testing And Troubleshooting
- Removal and Installation
- APP Sensor Signal Inspection
- Air Cleaner Element Inspection
- Block and Piston Inspection
- Camshaft Inspection
- Camshaft Timing Inspection
- Connecting Rod Bearing Adjustment
- Connecting Rod and Crankshaft End Play Inspection
- Crankshaft Inspection
- Crankshaft Main Bearing Adjustment
- Cylinder Bore Honing
- Engine Compression Inspection
- Engine Oil Jet Inspection
- Engine Removal and Installation
- Engine Support Hanger Installation
- Idle Speed Inspection
- Injector Removal and Installation
- Intake Manifold Removal and Installation
- PCM Idle Learn Procedure
- PCM Reset
- PCM Update
- PCV Valve Inspection
- Piston, Ring, Pin, and Connecting Rod Inspection
- Three Way Catalytic Converter Inspection
- Throttle Body Carbon Accumulation Check
- Throttle Body Cleaning
- VTC Actuator Inspection
- VTC Oil Control Solenoid Valve Test
- Valve Inspection
- Valve Seat Reconditioning
- Valve Stem-to-Guide Clearance Inspection
- Variable Cylinder Management (VCM) Test
- Symptom Troubleshooting Index for Viewer
- After warming up, idle speed is above specifications without load (MIL works OK, no DTCs set) (PGM-FI System)
- After warming up, idle speed is below specifications without load (MIL works OK, no DTCs set) (PGM-FI System)
- Auto idle stop system does not operate (Auto Idle Stop System)
- Auto idle stop system indicator does not come on:Auto idle stop indicator (green) Auto idle stop system indicator (amber) Auto idle stop OFF indicator (white) Auto idle stop suspend indicator (white) (Auto Idle Stop System)
- Cold fast idle too high (MIL works OK, no DTCs set) (PGM-FI System)
- Cold fast idle too low (MIL works OK, no DTCs set) (PGM-FI System)
- Difficult to refuel(MIL works OK, NO DTCs set) (PGM-FI System)
- Engine is hard to start (MIL works OK, no DTCs set)(PGM-FI System)
- Engine stalls (MIL works OK, no DTCs set) (PGM-FI System)
- Engine starts but stalls immediately (MIL works OK, no DTCs set, security indicator stays on or flashes) (PGM-FI System)
- Engine will not start (MIL works OK, no DTCs set) (PGM-FI System)
- Engine will not start (MIL works OK, no DTCs set, security indicator stays on or flashes) (PGM-FI System)
- Engine will not start and HDS does not communicate with the PCM(MIL comes on and stays on, no DTCs set) (PGM-FI System)
- HDS does not communicate with the PCM or the vehicle (PGM-FI System)
- Idle speed fluctuates (MIL works OK, no DTCs set) (PGM-FI System)
- Idle stop time is short (Auto Idle Stop System)
- Low power (MIL works OK, no DTCs set)(PGM-FI System)
- MIL comes on and stays on, or never comes on at all, no DTCs set (PGM-FI System)
- Starter system warning message displays on (no DTCs set) (Auto Idle Stop System)
- Troubleshooting
- Inspection
- Description and Operation
- Auto Idle Stop System Description
- Auto Idle Stop System Description - Operation Conditions
- EVAP System Description
- Electronic Throttle Control System Description
- PCV System Description
- PGM-FI System Description
- PGM-FI System Description - Components
- PGM-FI System Description - On-Board Snapshot
- Shutter Grille System Description
- Variable Cylinder Management (VCM)/VTC System Description
- General Information
- (Guidance) - Powertrain
- How to read
- Guidance
- Tighten bolts and nuts according to the service manual. (Torque control method, Rotation angle method)
- Tightening Bolts/Nuts According to the Hole Shape
- Tightening Order of Bolts or Nuts with Different Sizes
- Tightening Hose Bands and Clamps
- Preventing Parts from Falling
- When Moving Parts with Hoses and Pipes
- Keeping the Connectors Free of Liquids and Debris Before Disconnecting Them
- Mounting Parts that are Spring Loaded
- Engine Configuration
- How to Connect the HDS
- How to Set Readiness Codes
- Malfunction Indicator Lamp (MIL) Indication (In Relation to Readiness Codes)
- Catalytic Converter Monitor and Readiness Code
- Evaporative Emission (EVAP) Control System Monitor and Readiness Code
- Air Fuel Ratio (A/F) Sensor Monitor and Readiness Code
- Air Fuel Ratio (A/F) Sensor Heater Monitor Readiness Code
- Misfire Monitor and Readiness Code
- Fuel System Monitor and Readiness Code
- Comprehensive Component Monitor and Readiness Code
- EGR Monitor and Readiness Code
- (Guidance) - Powertrain
- Connector View
- Component Location Index
- Symptom Troubleshooting Index