Repair Procedures: Removal

1. Turn ignition switch OFF and disconnect the negative (-) battery cable.
2. Remove the engine cover.

   (Refer to Engine Mechanical System - "ENGINE COVER ")

3. Remove the air cleaner assembly and air duct.

   (Refer to Engine Mechanical System - "AIR CLEANER ")

4. Remove the battery and battery tray.

   (Refer to Engine Electrical System - "BATTERY ")

5. Disconnect the solenoid valve connector (B) and inhibitor switch connector (A).

   Courtesy of HYUNDAI MOTOR AMERICA

6. Remove the fixing clips (A) of wiring.

   Courtesy of HYUNDAI MOTOR AMERICA

   Courtesy of HYUNDAI MOTOR AMERICA

7. Remove the ground line after removing the bolt (A).

   Courtesy of HYUNDAI MOTOR AMERICA

8. Remove the shift cable (C) after removing the nut (A) and bolt (B).

   Tightening Torque: 

   (B) 14.7 - 21.6 N.m (1.5 - 2.2 kgf.m, 10.9 - 15.9 lb-ft) (A) 9.8 - 13.7 N.m (1.0 - 1.4 kgf.m, 7.2 - 10.1 lb-ft)

   Courtesy of HYUNDAI MOTOR AMERICA

   Courtesy of HYUNDAI MOTOR AMERICA

9. Disconnect the hose (A) after removing the automatic transaxle fluid cooler hose clamp.

   Courtesy of HYUNDAI MOTOR AMERICA

   CAUTION:

   • Carefully install the clamp not to damage the hose.
   • Install the clamp in a correct direction not to be interfered with other parts.
   • After the installation, start the engine and then check if there are any leakages from the hose.
10. Remove the cowl top cover. (Refer to Body - "COWL TOP COVER ")
11. Assemble the Engine Support Fixture (Beam No.: 09200-38001 or 09200-3N000, supporter No.: 09200-2S000, adapter No.: 09200-2W000).

    (Refer to SPECIAL SERVICE TOOLS - "Engine Support Fixture Assembly Drawing")

12. Using the engine support fixture (A), hold the engine and transaxle assembly safely.

    Courtesy of HYUNDAI MOTOR AMERICA

13. Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter mounting bolt (B-2ea).

    Tightening Torque: 

    (A) 42.2 - 54.0 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb-ft)

    (B) 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft)

    Courtesy of HYUNDAI MOTOR AMERICA

14. Remove the automatic transaxle mounting bracket cover (A).

    Courtesy of HYUNDAI MOTOR AMERICA

15. Remove the automatic transaxle support bracket mounting bolts (A).

    Tightening torque: 

    88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.8 lb-ft)

    Courtesy of HYUNDAI MOTOR AMERICA

16. Remove the automatic transaxle support bracket (A).

    Tightening torque: 

    58.8 - 78.5 N.m (6.0 - 8.0 kgf.m, 43.4 - 57.9 lb-ft)

    Courtesy of HYUNDAI MOTOR AMERICA

17. Lift the vehicle with a jack.
18. Remove the under cover.

    (Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ")

19. Remove the drive shaft assembly.

    (Refer to Driveshaft and Axle - "FRONT DRIVESHAFT ")

20. Remove the dust cover (A).

    Courtesy of HYUNDAI MOTOR AMERICA

21. Remove the Torque Converter Mounting Bolts (A) with rotating the crankshaft.

    Tightening Torque: 

    45.1 - 52.0 N.m (4.6 - 5.3 kgf.m, 33.3 - 38.3 lb-ft)

    Courtesy of HYUNDAI MOTOR AMERICA

22. Remove the roll rod bracket (C) after removing the bolt (A) and (B).

    Tightening Torque: 

    Bolt (B): 107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)

    Bolt (A): 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft)

    Courtesy of HYUNDAI MOTOR AMERICA

23. Remove the roll road support bracket (D).

    Tightening Torque: 

    49.0 - 68.6 N.m (5.0 - 7.0 kgf.m, 36.2 - 50.6 lb-ft)

    Courtesy of HYUNDAI MOTOR AMERICA

24. Remove the automatic transaxle with a jack after removing the mounting bolts (A, B).

Tightening Torque: 

(A) 42.2 - 53.9 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb-ft)

(B) 42.2 - 48.1 N.m (4.3 - 4.9 kgf.m, 31.1 - 35.4 lb-ft)

Courtesy of HYUNDAI MOTOR AMERICA