Precaution for Brake Control system

WARNING: This page is about a different car, the 2011 Nissan Leaf. However, it is still accessible from the selected car via links, so may be relevant.

Always perform a pre-driving check to drive the vehicle.
Always check speed and safety while driving the vehicle.
To operate CONSULT while driving, more than one person is required to be in the vehicle to avoid interference to driving and ensure safety.
Slight vibrations are felt on the brake pedal and the operation noises occur, when VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function or brake assist function operates. This is not a malfunction because it is caused by VDC function, TCS function, ABS function EBD function brake limited slip differential (BLSD) function or brake assist function that is normally operated.
When power switch ON or when starting vehicle just after power switch ON, brake pedal may vibrate or motor operating noise may be heard from traction motor compartment. This is normal condition.
Brake stopping distance may become longer than models without ABS function depending on the road conditions, when ABS function is operated on slippery road like rough road, gravel road or snowy road.
When a malfunction is indicated, always collect information from the customer about conditions of occurrence, estimate cause and perform operation. Check brake booster operation, brake fluid level and brake fluid leakage, as well as electrical system.
The optimum performance is achieved by control for VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function and brake assist function when all of brakes, suspensions and tires installed on the vehicle are the specified size and parts. Brake performance and controllability may be negatively affected when other parts than the specified are installed.
Brake stopping distance may become longer and steering stability may be negatively affected, when tires in different size and combination or other parts than the specified are used.
When a radio (including wiring), antenna and antenna lead line are located near ABS actuator and electric unit (control unit), a malfunction or improper operation may occur for the control of VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function and brake assist function.
When the following items are replaced by other parts than genuine parts or modified, ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, and the control may not operate normally for VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function and brake assist function.
- Suspension component parts (shock absorber, spring, bushing and others)
- Tire and wheel (other than the specified size)
- Brake component parts (brake pad, disc rotor, brake caliper and others)
- Traction motor component parts (VCM, traction motor inverter)
- Body reinforcement component parts (rollover bar, tower bar and others)
When suspension, tire and brake component parts are excessively worn or deteriorated and the vehicle is driven, ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, and the control may not operate normally for VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function and brake assist function.
ABS warning lamp, brake warning lamp and VDC warning lamp may turn ON, when only front wheel or rear wheel is rotated using a free roller. This is not a malfunction, because it is caused by wheel speed difference between wheel that is rotated and wheel that is not rotated. In this case, perform self-diagnosis, check self-diagnosis results, and erase memory.
CAUTION:
- Be sure to wait of 10 seconds after turning power switch OFF or ON.
- Turn power switch from OFF → ON before self-diagnosis. Repeat two or more times.
- Set the vehicle to READY.
- Turn the power switch OFF → ON → OFF after erase self-diagnosis result.
When power supply voltage is not normal, ABS warning lamp, brake warning lamp and VDC warning lamp turn ON. ABS actuator and electric unit (control unit) stops control for VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function and brake assist function. Ordinary brake operates. After power supply returns to normal, ABS warning lamp, brake warning lamp and VDC warning lamp turn OFF. The control becomes operative for VDC function, TCS function, ABS function EBD function, brake limited slip differential (BLSD) function and brake assist function.
Brake pedal vibrates and operation sound occurs during sudden acceleration and cornering, when VDC function, TCS function, brake limited slip differential (BLSD) function or brake assist function is operated. This is not a malfunction because it is caused by VDC function, TCS function, brake limited slip differential (BLSD) function or brake assist function that is operated normally.
VDC warning lamp may turn ON and VDC function, TCS function, brake limited slip differential (BLSD) function and brake assist function may not normally operate, when driving on a special road the is extremely slanted (bank in a circuit course). This is not a malfunction if the status returns to normal for VDC function, TCS function, brake limited slip differential (BLSD) function and brake assist function after the traction motor is started again. In this case, perform self-diagnosis, check self-diagnosis results, and erase memory.
CAUTION:
- Be sure to wait of 10 seconds after turning power switch OFF or ON.
- Turn power switch from OFF → ON before self-diagnosis. Repeat two or more times.
- Set the vehicle to READY.
- Turn the power switch OFF → ON → OFF after erase self-diagnosis result.
A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle sharply turns during a spin turn, acceleration turn or drift driving while VDC function, TCS function and brake limited slip differential (BLSD) function are OFF (VDC OFF switch is pressed and VDC OFF indicator lamp is in ON status). This is not a malfunction if the status returns to normal for VDC function, TCS function and brake limited slip differential (BLSD) function after the traction motor is started again. In this case, perform self-diagnosis, check self-diagnosis results, and erase memory.
CAUTION:
- Be sure to wait of 10 seconds after turning power switch OFF or ON.
- Turn power switch from OFF → ON before self-diagnosis. Repeat two or more times.
- Set the vehicle to READY.
- Turn the power switch OFF → ON → OFF after erase self-diagnosis result.