Torque Specifications
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Accessory drive belt tensioner | 38-48 | - | - |
| Accessory drive belt idler pulley | 53-69 | - | - |
| Air intake tube to throttle body | 4-5 | - | - |
| A/C pipes to receiver / drier | 8-10 | - | - |
| A/C pipe manifold joints | 8-10 | - | - |
| Camshaft bearing caps | 9-11 | - | - |
| Camshaft cover | 9-11 | - | - |
| Charge Air Cooler Adaptor to cylinder head (SC) | 20-22 | - | - |
| Crankshaft damper bolt - no locking ring | 80 + 80° | - | - |
| Crankshaft damper bolt - with locking ring | 364-386 | - | - |
| Crankshaft position sensor | 8-12 | - | - |
| Cylinder head bolts M10 | 35 | - | - |
| Cylinder head bolts M8 (two at front of head) | 23-27 | - | - |
| Driveshaft (propshaft) drive flange bolts | 75-88 | - | - |
| ERG pipe to exhaust manifold | 18-24 | - | - |
| Engine compartment cover (bonnet) hinges | 22-28 | - | - |
| Engine coolant radiator top securing panel | 22-28 | - | - |
| Engine front mounting | 60-80 | - | - |
| Engine oil cooler pipes (clamp) | 18-24 | - | - |
| Engine / Transmission assembly rear mounting center bolt | 30-40 | - | - |
| Engine / Transmission assembly rear mounting outer bolts | 22-28 | - | - |
| Exhaust downpipe support bracket to flywheel housing | 43-57 | - | - |
| Exhaust downpipe to lower mounting bracket | 42-54 | - | - |
| Exhaust camshaft sprocket | 115-125 | - | - |
| Exhaust manifold to cylinder head | 116-20 | - | - |
| Exhaust manifold flange to downpipe | 115-20 | - | - |
| Exhaust Torca clamps | 50-60 | - | - |
| Fuel cross-over elbow | 8-12 | - | - |
| Fuel feed pipe to intake manifold | 8-12 | - | - |
| Fuel injector harness clips to camshaft cover (SC) | 4-5 | - | - |
| Fuel pressure regulator to intake manifold | 8-12 | - | - |
| Fuel rail to Charge Air Cooler Adaptor (SC) | 18-24 | - | - |
| Intake manifold to cylinder heads | 20-22 | - | - |
| Intake elbow support brackets | 16-20 | - | - |
| Oil filter | 15-18 | - | - |
| Oil Cooler | 7 | - | - |
| PAS pump hose unions | 22-28 | - | - |
| Primary timing chain fixed guide | 10-14 | - | - |
| Primary timing chain tensioner | 10-14 | - | - |
| Primary timing chain tensioner blade | 12-16 | - | - |
| Secondary timing chain tensioner to cylinder | 10-14 | - | - |
| Steering rack | 40-50 | - | - |
| Throttle body to intake elbow | 18-24 | - | - |
| Throttle cable abutment to throttle body | 4-6 | - | - |
| Throttle intake elbow to intake manifold | 18-24 | - | - |
| Timing cover | 11-13 | - | - |
| Variable camshaft timing oil control unit to intake camshaft | 40 + 90° | - | - |
| Variable camshaft timing oil control unit housing (bolt and nut) | 119-23 | - | - |
| Variable camshaft timing oil control solenoid | 10-14 | - | - |
| Water pump pulley | 10-14 | - | - |