Warning Screen

When malfunctions occur to the vehicle, the following warning screens are displayed. If these screens are not displayed normally or if they continue to be displayed even after the factor is eliminated, take measures according to the action procedure.

Display content	Message	Factor	Action procedure
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	TURN OFF LIGHTS	Displayed with the sounding of tone alarm when the driver's door is opened with the electric motor switch at the OFF or ACC position and the lighting switch at the tail or head position.	If the lighting monitor warning tone alarm is not being sounded, perform the troubleshooting for the lighting monitor warning tone alarm. Refer to INSPECTION PROCEDURE 6: TONE ALARMS DO NOT SOUND NORMALLY  .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	KEY BATTERY LOW	Displayed when the keyless operation key battery is running low.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the KOS. Refer to DIAGNOSTIC TROUBLE CODE CHART <KOS-ECU> .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	KEY NOT DETECTED	Displayed if carrying a keyless operation key with different ID code or the keyless operation key is outside the operative range.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	KEY STILL IN VEHICLE	Displayed when the keyless operation key take-out monitoring function or keyless operation key confinement prevention function is in operation.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CHECK DOORS	Displayed when the door ajar prevention function is in operation.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	KEYLESS OPERATION SYSTEM SERVICE REQUIRED	Displayed when there is a malfunction to KOS.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the KOS. Refer to DIAGNOSTIC TROUBLE CODE CHART <KOS-ECU> .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	KEY NOT DETECTED INSERT KEY INTO KEY SLOT	Displayed when the keyless operation key cannot be detected.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	REMOVE KEY FROM KEY SLOT	Displayed when the key is not removed from the key slot located in the glove box.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	-	Displayed when the lock/unlock switch of front door outside handle is pressed while in the power mode other than OFF.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	-	Displayed when the driver's door is open while in the power mode other than OFF.	If the warning screen is not displayed or if the screen continues to be displayed, perform the troubleshooting for the OSS. Refer to DIAGNOSTIC TROUBLE CODE CHART <OSS-ECU> .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	IMMOBILIZER SYSTEM SERVICE REQUIRED	Displayed when a malfunction occurs to the immobilizer system.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	SHIFT TO P POSITION	Displayed when the plug-in hybrid EV system is stopped while the selector lever is in other than P position.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the OSS. Refer to DIAGNOSTIC TROUBLE CODE CHART <OSS-ECU> .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	STEERING WHEEL UNLOCKED	Displayed when the steering lock is not in operation.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ELECTRICAL SYSTEM SERVICE REQUIRED	Displayed when a malfunction occurs to the power supply system.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	PRESS BRAKE PEDAL TO START	Displayed when the electric motor switch is pressed without the brake pedal depressed at starting the plug-in hybrid EV system.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	LOW TIRE PRESSURE	Displayed when the type air pressure is an abnormality. (except spare type)	If the warning screen is not displayed normally or erased, carry out the troubleshooting for the TPMS (Refer to DIAGNOSTIC TROUBLE CODE CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	TIRE PRESSURE MONITOR SERVICE REQUIRED	Displayed when the TPMS is an abnormality.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ABS SERVICE REQUIRED	Displayed when a malfunction occurs to the anti-lock braking system (ABS).	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the ABS or ASC. Refer to DIAGNOSTIC TROUBLE CODE CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ENGINE OVERHEATING STOP SAFELY	Displayed when overheated.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the engine. Refer to SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	FASTEN SEAT BELT	Displayed when the electric motor switch is turned ON without the driver's seat belt fastened.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the seat belt reminder warning lamp. (Refer to INSPECTION PROCEDURE 8: THE COMBINATION METER LIGHT DOES NOT ILLUMINATE NORMALLY OR THE MULTI-INFORMATION DISPLAY IS NOT DISPLAYED NORMALLY  .)
	PUSH SWITCH AFTER FASTENING SEAT BELT	Displayed when the driver operates the brake auto hold switch to switch the brake auto hold function from OFF to the on (stand by) mode with the seat belt unfastened.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the electric parking brake. Refer to TROUBLE SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	FUEL SYSTEM SERVICE REQUIRED	Displayed when there is a malfunction to the fuel system.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the combination meter DTC. Refer to INSPECTION PROCEDURE 8: THE COMBINATION METER LIGHT DOES NOT ILLUMINATE NORMALLY OR THE MULTI-INFORMATION DISPLAY IS NOT DISPLAYED NORMALLY  .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	REFUEL	Displayed when the remaining fuel amount is small.	If the warning screen is not displayed normally or if the screen continues to be displayed, refuel immediately.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	LOW OIL PRESSURE	Displayed when there is a malfunction to the engine oil circulation system.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the oil pressure. (Refer to ENGINE OIL PRESSURE CHECK .) Then if the oil pressure is normal, perform the troubleshooting for the engine. (Refer to SYMPTOM CHART .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	AIRBAG SYSTEM SERVICE REQUIRED	Displayed when there is a malfunction to the SRS air bag or to the pre-tensioner mechanism.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the SRS air bag/pre-tensioner mechanism warning light. Refer to TROUBLE SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ASC SYSTEM SERVICE REQUIRED	Displayed when there is a malfunction to the ASC.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the ASC. Refer to TROUBLE SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	POSSIBLE ICY ROADS	Displayed with the sounding of tone alarm when the ambient temperature is 3°C (37°F) or less.	If the warning tone alarm does not sound when the combination meter displays 3°C (37°F), perform the troubleshooting for the freeze warning tone alarm. Refer to INSPECTION PROCEDURE 6: TONE ALARMS DO NOT SOUND NORMALLY  .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	POWER STEERING SERVICE REQUIRED	Displayed when there is a malfunction to the EPS.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the EPS. Refer to TROUBLE SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	-	If any of the doors or liftgate is not closed completely, the location of the ajar door is displayed with the sounding of tone alarm.	If the door ajar warning tone alarm does not sound, perform the troubleshooting for the door ajar warning tone alarm. Refer to INSPECTION PROCEDURE 6: TONE ALARMS DO NOT SOUND NORMALLY  .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CLOSE HOOD	Displayed when the hood is open.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the hood latch switch input signal. Refer to INSPECTION PROCEDURE 14: THE HOOD LATCH SWITCH SIGNAL IS NOT RECEIVED .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	-	Is displayed when your vehicle may collide with a vehicle-travelling-ahead.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the FCM/LDW/AHB-ECU DTC. Refer to DIAGNOSTIC TROUBLE CODE CHART .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	FCM BRAKE ACTIVATED	Is displayed after the FCM turns off.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	FCM SERVICE REQUIRED	Is displayed when the FCM is defective.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	FCM TEMPORARILY NOT AVAILABLE	Is displayed when the FCM is inactive temporarily.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	-	Displayed when the vehicle-travelling-ahead is decelerating too much, another vehicle interrupts your lane, or your vehicle is too close to the vehicle-travelling-ahead due to poor deceleration on downhill while the ACC is in progress.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the ACC DTC. Refer to CHECK CHART FOR DIAGNOSTIC TROUBLE CODES .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ACC SERVICE REQUIRED	Displayed when the ACC system has some abnormality.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ACC CANCELLED	Displayed when ACC stops due to one of the following conditions. When the ASC is turned off. When ABS or ASC is in operation. When the parking brake is applied. When the selector lever is in the "P", "R" or the "N" position. When the driver's seat belt is unfastened. When the driver's door is opened. When the ACC no longer detects any vehicle in front while it is in the stationary vehicle hold state. When the vehicle is stationary for 10 minutes or more. When the system detects the vehicle sliding down a slope.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the ACC DTC. Refer to CHECK CHART FOR DIAGNOSTIC TROUBLE CODES .
	ACC NOT AVAILABLE NOW	Conditions for the start of control are not met, the ACC cannot start the control.
	ACC OUT OF SPEED RANGE	The ACC cannot start the control because the speed is out of speed range.
	ACC NO FORWARD VEHICLE	The ACC cannot start the control because not detected the approach of the vehicles in front.
	ACC TEMPORARILY NOT AVAILABLE RADAR BLOCKED	The ACC is not available temporarily such as for adhesion of contaminants to the sensor. This is not a malfunction.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	ACC SERVICE REQUIRED	There is a fault in the adaptive cruise control system (ACC).	If the warning screen is not displayed normally or if the screen continues to be displayed, check the adaptive cruise control system (ACC) DTC. (Refer to CHECK CHART FOR DIAGNOSTIC TROUBLE CODES .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	APPLY BRAKE	If the vehicle-travelling-ahead stops during the ACC operation, your vehicle will also stop automatically. When the driver does not depress the brake pedal under this condition, this icon will appear. Displayed when the brake is released (the auto hold function is deactivated). (In normal way, when the ASC fluid pressure is reached, the EPB controls the brake. However, this icon is displayed when the parking brake cannot be applied due to a EPB failure.)	If the warning screen is not displayed normally or if the screen continues to be displayed, check the ACC DTC. (Refer to CHECK CHART FOR DIAGNOSTIC TROUBLE CODES .) If the warning screen is not displayed normally or if the screen continues to be displayed, check the ASC DTC. (Refer to DIAGNOSTIC TROUBLE CODE CHART .)
	PUSH SWITCH WHILE APPLYING BRAKE	Displayed when the switch is operated without depressing the brake pedal while the brake auto hold function is deactivated.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the ASC DTC. (Refer to DIAGNOSTIC TROUBLE CODE CHART .)
-	LANE DEPARTURE	A message will appear when the system enters the warning condition.	If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the LDW. (Refer to DIAGNOSTIC TROUBLE CODE CHART .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	LDW SERVICE REQUIRED	Displayed when the LDW system is defective.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	BSW TEMPORARILY NOT AVAILABLE	Displayed when any of the conditions below is satisfied. Abnormal internal temperature in the ECU The sensors in the ECU are out of permissible temperature range The sensor in the ECU receives noise.	If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the BSW. (Refer to DIAGNOSTIC TROUBLE CODE CHART <BSW-ECU (MASTER)> or DIAGNOSTIC TROUBLE CODE CHART <BSW-ECU (SLAVE)> .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	BSW SERVICE REQUIRED	Displayed when the BSW-ECU fails due to open circuit in the sensor inside the BSW-ECU.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	BSW RADAR BLOCKED	Displayed when the BSW cannot function due to a foreign material adhered on the sensor.
-	ATTENTION! REAR CROSS TRAFFIC	Displayed when an approaching vehicle is detected behind your vehicle during reversing.	If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the RCTA. (Refer to DIAGNOSTIC TROUBLE CODE CHART <BSW-ECU (MASTER)> .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	LED HEADLIGHT SERVICE REQUIRED	The LED type headlights are defective.	If the warning screen is not displayed normally or if the screen continues to be displayed, troubleshoot the headlights. (Refer to TROUBLE SYMPTOM CHART .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	BRAKE SYSTEM SERVICE REQUIRED	Displayed when the brake fluid amount is insufficient or a malfunction occurs to the brake device.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the brake fluid or brake device. Refer to BLEEDING .
	RELEASE PARKING BRAKE	Displayed when the electric parking brake is activated during driving	If the warning screen is not displayed normally or if the screen continues to be displayed, check the parking brake. Refer to TROUBLE SYMPTOM CHART .
	PARKING BRAKE ENGAGED	When any of the conditions below is satisfied while the auto hold function holds the vehicle stationary, the electric parking brake will be activated. The oil pressure is held for at least ten minutes. Unfasten the seat belt (driver's side). Open the door. The system detects the movement of the vehicle. Electric motor switch: OFF	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the electric parking brake. Refer to TROUBLE SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	PARKING BRAKE SERVICE REQUIRED	Displayed when a malfunction occurs to the electric parking brake.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	PARKING BRAKE TEMPORARILY NOT AVAILABLE	Displayed when the electric parking brake is inactive temporarily.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the electric parking brake. Refer to TROUBLE SYMPTOM CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	PRESS BRAKE PEDAL TO RELEASE	You try to release the electric parking brake switch without depressing the brake pedal.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	BRAKE AUTO HOLD CANCELED	Displayed when the auto hold function is cancelled under any of the conditions below with the brake auto hold function operationally ready. The driver operates the brake auto hold switch. The electric parking brake fails The ASC fails	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the electric parking brake. Refer to TROUBLE SYMPTOM CHART .
	BRAKE AUTO HOLD NOT AVAILABLE	Displayed when the system cannot be resumed to a stand by mode although the driver operates the brake auto hold switch under any of the conditions below: The electric parking brake fails The brake auto hold function fails
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	RBS SERVICE REQUIRED	Displayed when the Regenerative brake is defective.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the regenerative brake system DTC (Refer to DIAGNOSTIC TROUBLE CODE CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	PROPULSION POWER IS REDUCED	Displayed when drive limitations are activated as the main drive lithium-ion battery charged level is low or the plug-in hybrid EV system is too hot or cold.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the BMU, Main drive lithium-ion battery (Refer to INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	BATTERY TOO COLD	Displayed when the temperature in the module reduces to -30°C (86°F) or less.
	BATTERY TOO COLD PLUG IN NORMAL CHARGER TO WARM	The main drive lithium-ion battery is extremely cold temperature. The Plug-in Hybrid EV System will not start until the main drive lithium-ion battery is warm enough.	Even if the main drive lithium-ion battery is full charge, connect EV charging cable (normal charger). Then, the main drive lithium-ion battery warming system is operated, the main drive lithium-ion battery is automatically warmed up. While the main drive lithium-ion battery warning system is operating, "BATTERY TOO COLD" will be displayed. If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the BMU, Main drive lithium-ion battery (Refer to INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE ).
	BATTERY TOO COLD FOR VEHICLE TO OPERATE	The main drive lithium-ion battery is extremely cold temperature.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the BMU, Main drive lithium-ion battery (Refer to INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	EV SYSTEM SERVICE REQUIRED	Displayed when errors occur in the plug-in hybrid EV system (however, the vehicle can be driven).	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the PHEV-ECU (Refer to DIAGNOSTIC TROUBLE CODE CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	EV SYSTEM SERVICE REQUIRED STOP SAFELY	Displayed when errors occur in the plug-in hybrid EV system (the vehicle cannot be driven).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	SHIFT TO P POSITION	Displayed when the selector lever is at any position other than "P" while the plug-in hybrid EV system is deactivated.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the electrical parking driver unit DTC (Refer to DIAGNOSTIC TROUBLE CODE CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	P LOCK MALFUNCTION WHEN PARKING, APPLY PARKING BRAKE SECURELY	Displayed when the electric motor unit cannot be deactivated because there is a fault with the parking switch.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	SHIFT TO N POSITION	Displayed when you move the selector lever to the N range and then depress the accelerator pedal.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the electrical parking driver unit DTC (Refer to DIAGNOSTIC TROUBLE CODE CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	APPLY BRAKE WHILE SHIFTING	The selector lever has been operated when the select position is in "P" (PARK) position and the brake pedal is not depressed.	Operate the selector lever while depressed firmly on the brake pedal.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	TO CONSUME OLD FUEL REFUEL 15L (4GAL) OR MORE	Displayed when the system starts the engine forcibly to consume deteriorated fuel because the engine has not run for a long time.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the engine (Refer to SYMPTOM CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CHARGE CABLE CONNECTED	Displayed when you attempt to turn on the power supply mode of the electric motor switch while a charging connector (gun) is connected to the charging connector.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the BMU, Main drive lithium-ion battery (Refer to INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CHARGE INTERRUPTED BY SYSTEM MALFUNCTION	Displayed when the battery charging is cancelled because there is an error (electric leakage) in the system.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the BMU, Main drive lithium-ion battery (Refer to INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CHARGE STOPPED	Displayed when the charging cable is connected improperly or the battery charging is cancelled due to power failure.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CHARGE COMPLETE	Displayed when the drive battery has been charged fully.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CHARGE LID IS OPEN	Displayed when the charging lid is open.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the BMU, Main drive lithium-ion battery (Refer to INSPECTION CHART FOR DIAGNOSTIC TROUBLE CODE ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	-	Displayed when the FCM is deactivated.	If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the FCM (Refer to DIAGNOSTIC TROUBLE CODE CHART ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	DRIVER ASSISTANCE CAMERA SERVICE REQUIRED	Displayed when the camera incorporated in the FCM/LDW/AHB-ECU fails.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the FCM/LDW/automatic high beam system DTC. (Refer to DIAGNOSTIC TROUBLE CODE CHART .)
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	DRIVER ASSISTANCE CAMERA TEMPORARILY NOT AVAILABLE	Displayed when a system (FCM, automatic high beam system or LDW) is inoperational temporarily due to too high temperature in the FCM/LDW/AHB-ECU camera.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	DRIVER ASSISTANCE CAMERA BLOCKED	Displayed when a system (FCM, automatic high beam system or LDW) is inoperational temporarily, because the FCM/LDW/AHB-ECU camera is contaminated or sunlight is reflected on the camera.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	UNCALIBRATED	Displayed when the camera in the FCM/LDW/AHB-ECU has not been calibrated yet.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	CALIBRATING	Displayed when the camera in the FCM/LDW/AHB-ECU is being calibrated.
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	AHB SERVICE REQUIRED	Displayed when the automatic high beam system fails	If the warning screen is not displayed normally or if the screen continues to be displayed, check the automatic high beam system troubleshooting. Refer to DIAGNOSTIC TROUBLE CODE CHART .
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	LOW WASHER FLUID	Low washer fluid level.	If the warning screen is not displayed normally or if the screen continues to be displayed, check the windshield washer (Refer to INSPECTION ).
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.	EV MODE NOT AVAILABLE BATTERY CHARGE LOW	Displayed when certain vehicle conditions do not allow the system to enter the EV mode although the driver operates the switch. Displayed when the engine is running.	If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the PHEV-ECU (Refer to TROUBLE SYMPTOM CHART ).
	EV MODE NOT AVAILABLE CRUISE CONTROL SET	EV priority mode is not available because the cruise control or the Adaptive Cruise Control System (ACC) is operating.
	EV MODE NOT AVAILABLE	Displayed when certain vehicle conditions do not allow the system to enter the EV mode although the driver operates the switch. Displayed during harsh acceleration.
	EV MODE CANCELED BATTERY CHARGE LOW	Displayed when the EV mode must be cancelled due to certain vehicle condition. Displayed when the engine is running.
	EV MODE CANCELED CRUISE CONTROL SET	EV priority mode is canceled because the vehicle speed of the cruise control or the Adaptive Cruise Control System (ACC) is set.
	EV MODE CANCELED	Displayed when the EV mode must be cancelled due to certain vehicle condition. During harsh acceleration.