lemon-mirror:
Home >> Scion >> 2008 >> xB Automatic >> Repair and Diagnosis >> Transmission >> Automatic Trans >> U241E Automatic Transaxle >> Transmission Control Cable Assembly >> Removal

Transmission Control Cable Assembly: Removal

  1. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL  (See REMOVAL )
  2. REMOVE FRONT NO. 2 CONSOLE BOX INSERT  (See REMOVAL )
  3. REMOVE FRONT NO. 1 CONSOLE BOX INSERT  (See REMOVAL )
  4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL  (See REMOVAL )
  5. REMOVE BATTERY  (See REMOVAL )
  6. REMOVE NO. 2 BATTERY CARRIER  (See REMOVAL  )
  7. REMOVE AIR CLEANER CAP SUB-ASSEMBLY  (See REMOVAL )
  8. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY  (See REMOVAL  )
  9. REMOVE AIR CLEANER CASE SUB-ASSEMBLY  (See REMOVAL  )
  10. REMOVE CENTER EXHAUST PIPE ASSEMBLY 
    1. Remove the 2 bolts and gasket and separate the center exhaust pipe assembly from the front exhaust pipe assembly.
      Fig 1: Locating Center Exhaust Pipe Assembly Bolts And Gasket
      G05388129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 bolts, 2 compression springs and separate the center exhaust pipe assembly from the No. 2 center exhaust pipe assembly.
      Fig 2: Locating No. 2 Center Exhaust Pipe Assembly Bolts And Compression Springs
      G05388130Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 2 exhaust pipe supports, then remove the center exhaust pipe assembly.
      Fig 3: Locating Exhaust Pipe Supports
      G05388131Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR 
    1. Remove the 3 nuts and remove the front No. 1 floor heat insulator.
      Fig 4: Locating Nuts And Front No. 1 Floor Heat Insulator
      G05388132Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Disconnect the 2 connectors.
      Fig 5: Locating Connectors
      G05388089Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the transmission control cable assembly from the shift lever.
      Fig 6: Identifying Transmission Control Cable Assembly
      G05388090Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a screwdriver, pull out the stopper of the transmission control cable.
      NOTE: Do not remove the stopper. If the stopper is removed, reinstall it to its original position.
      Fig 7: Identifying Transmission Control Cable Stopper
      G05388091Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.
      NOTE: Do not over-rotate the nut as it will come off the interior spring and the transmission control cable will not be reusable.
      Fig 8: Rotating Nut Counterclockwise
      G05388092Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the bolt and disconnect the transmission control cable assembly from the rear engine mounting insulator.
      Fig 9: Locating Bolt And Transmission Control Cable Assembly
      G05388137Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disconnect the transmission control cable assembly from the cable support clamp.
      Fig 10: Locating Cable Support Clamp
      G05388138Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.
    8. Remove the clip and disconnect the transmission control cable assembly from the transmission control cable bracket.
      Fig 11: Locating Transmission Control Cable Assembly Nut And Clip
      G05388139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Remove the 2 nuts and remove the transmission control cable assembly.
      Fig 12: Locating Nuts And Transmission Control Cable Assembly
      G05388140Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
· About lemon-mirror