lemon-mirror:
Home >> Subaru >> 2006 >> Baja Base, Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Engine (Diagnostics) (H4SO) >> Subaru Select Monitor >> Operation >> Read Current Data For Engine. (Normal Mode)

Read Current Data For Engine. (Normal Mode)

  1. On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
  2. On the «System Selection Menu» display screen, select the {Engine Control System} and press the [YES] key.
  3. Press the [YES] key after displayed the information of engine type.
  4. On the «Engine Diagnosis» display screen, select the {Current Data Display & Save} and press the [YES] key.
  5. On the «Data Display Menu» display screen, select the {Data Display} and press the [YES] key.
  6. Using the scroll key, move the display screen up or down until the desired data is shown.
SUPPORT DATA LIST

Contents Display Unit of measure
Battery voltage Battery Voltage V
Vehicle speed signal Vehicle Speed km/h or MPH
Engine speed signal Engine Speed rpm
Engine coolant temperature signal Coolant Temp. °C or °F
Ignition timing signal Ignition Timing deg
Throttle position signal Throttle Opening Angle %
Throttle position signal Throttle Sensor Voltage V
Injection pulse width Fuel Injection Width Pulse ms
Idle air control signal ISC Valve Step STEP
Engine load data Engine Load %
Front oxygen (A/F) sensor output signal A/F Sensor #1 -
Front oxygen (A/F) sensor resistance value A/F Sensor #1 resistance ohm
Rear oxygen sensor output signal Rear O2 Sensor V
Short term fuel trim A/F Correction #1 %
Knock sensor signal Knocking Correction deg
Atmospheric absolute pressure signal Atmosphere Pressure mmHg or kPa or inHg or psig
Intake manifold relative pressure signal Mani. Relative Pressure mmHg or kPa or inHg or psig
Intake manifold absolute pressure signal Mani. Absolute Pressure mmHg or kPa or inHg or psig
A/F correction (short term fuel trim) by rear oxygen sensor A/F Correction #3 %
Long term whole fuel trim A/F Learning #1 %
Front oxygen (A/F) sensor heater current Front O2 Heater #1 A
Rear oxygen sensor heater voltage Rear O2 Heater Voltage A
Canister purge control solenoid valve duty ratio CPC Valve Duty Ratio %
Fuel tank pressure signal Fuel Tank Pressure mmHg or kPa or inHg or psig
Fuel temperature signal Fuel Temp. °C or °F
Fuel level signal Fuel Level V
Intake air temperature signal Intake Air Temp. °C or °F
Learned ignition timing Learned Ignition Timing deg
EGR control signal No. of EGR Steps STEP
Identification signal of AT vehicle AT vehicle ID Signal AT/MT
Ignition switch signal Ignition Switch ON or OFF
Test mode connector signal Test Mode Signal ON or OFF
Neutral position switch signal Neutral Position Switch ON or OFF
Air conditioning switch signal A/C Switch ON or OFF
Air conditioning compressor signal A/C Compressor Signal ON or OFF
Radiator main fan relay signal Radiator Fan Relay #1 ON or OFF
Fuel pump relay signal Fuel Pump Relay ON or OFF
Knocking signal Knocking Signal ON or OFF
Radiator sub fan relay signal Radiator Fan Relay #2 ON or OFF
Engine torque control signal #1 Torque Control Signal #1 ON or OFF
Engine torque control signal #2 Torque Control Signal #2 ON or OFF
Engine torque control permission signal Torque Permission Signal ON or OFF
Rear oxygen sensor rich signal Rear O2 Rich Signal Rich/lean
Pressure control solenoid valve PCV Solenoid Valve ON or OFF
Drain valve Vent. Solenoid Valve ON or OFF
Starter switch signal Starter Switch ON or OFF
Idle switch signal Idle Switch Signal ON or OFF
Crankshaft position sensor signal Crankshaft Position Sig. ON or OFF
Fuel tank sensor control valve signal Fuel tank sensor control valve ON or OFF
Camshaft position sensor signal Camshaft Position Sig. ON or OFF
Rear defogger switch signal Rear Defogger Switch ON or OFF
Blower fan switch signal Blower Fan Switch ON or OFF
Small light switch signal Light Switch ON or OFF
Air assist injector solenoid valve signal Assist Air Sol. Valve ON or OFF
Power steering switch signal P/S Switch ON or OFF
Roughness Monitor for #1 cylinder Roughness Monitor #1 -
Roughness Monitor for #2 cylinder Roughness Monitor #2 -
Roughness Monitor for #3 cylinder Roughness Monitor #3 -
Roughness Monitor for #4 cylinder Roughness Monitor #4 -
NOTE:
  • For detailed operation procedure, refer to the Subaru Select Monitor Operation Manual.
  • For select monitor display details, refer to the following.