lemon-mirror:
Home >> Subaru >> 2006 >> Forester X, Automatic >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> Front Vehicle Speed Sensor >> Installation

Front Vehicle Speed Sensor: Installation

  1. Pass the transmission harness assembly through the hole in transmission case.
    Fig 1: Identifying Transmission Harness Assembly
    G05002532Courtesy of SUBARU OF AMERICA, INC.
  2. Connect the control valve connector and the grounding cable.

    Tightening torque: 

    8 N.m (0.8 kgf-m, 5.8 ft-lb) 

    Fig 2: Connecting Control Valve Connector And Grounding Cable
    G04994102Courtesy of SUBARU OF AMERICA, INC.
  3. Apply proper amount of liquid gasket to the entire oil pan mating surface.

    Liquid gasket: 

    Three bond 1217B (Part No. K0877YA020) 

    Fig 3: Applying Amount Of Liquid Gasket To Oil Pan Mating Surface
    G05002534Courtesy of SUBARU OF AMERICA, INC.
  4. Fill the 3 holes aside from the bolt holes in the transmission case, with liquid gasket.

    Liquid gasket: 

    Three bond 1217B (Part No. K0877YA020) 

    Fig 4: Locating Oil Pan Tightening Bolts
    G05002555Courtesy of SUBARU OF AMERICA, INC.
  5. Install the oil pan by equally tightening the bolts.

    Tightening torque: 

    5 N.m (0.5 kgf-m, 3.6 ft-lb) 

  6. Install the front vehicle speed sensor and torque converter turbine speed sensor.

    Tightening torque: 

    7 N.m (0.7 kgf-m, 5.1 ft-lb) 

  7. Connect the connector to the rear vehicle speed sensor.
  8. Install the ATF cooler inlet and outlet pipes.
    NOTE: Use a new copper washer.

    Tightening torque: 

    T1: 25 N.m (2.5 kgf-m, 18.1 ft-lb) 

    T2: 40 N.m (4.1 kgf-m, 29.5 ft-lb) 

    T3: 45 N.m (4.6 kgf-m, 33.2 ft-lb) 

    Fig 5: Connecting Connector To Rear Vehicle Speed Sensor
    G04994105Courtesy of SUBARU OF AMERICA, INC.
  9. Install the transmission rear crossmember bolt.

    Tightening torque: 

    70 N.m (7.1 kgf-m, 51 ft-lb) 

  10. Install the propeller shaft. <Ref. to INSTALLATION Propeller Shaft . >
  11. Install the heat shield cover. (If equipped)
  12. Install the front, center and rear exhaust pipes, and the muffler. (Non-turbo model)

    <Ref. to INSTALLATION Front Exhaust Pipe. > <Ref. to INSTALLATION Rear Exhaust Pipe. > <Ref. to INSTALLATION Muffler. >

  13. Install the center, rear exhaust pipes and the muffler. (Turbo model)

    <Ref. to INSTALLATION Center Exhaust Pipe. > <Ref. to INSTALLATION Rear Exhaust Pipe. > <Ref. to INSTALLATION Muffler. >

  14. Lower the vehicle.
  15. Install the transmission connector to the stay.
  16. Attach the pitching stopper. <Ref. to INSTALLATION  TRANSMISSION MOUNTING SYSTEM. >
  17. Install the air intake chamber. (Non-turbo model)

    <Ref. to INSTALLATION Air Intake Chamber. >

  18. Install the intercooler. (Turbo model)

    <Ref. to INSTALLATION Intercooler. >

  19. Pour in ATF.

    <Ref. to AUTOMATIC TRANSMISSION FLUID . >

  20. Bleed the air of control valve.

    <Ref. to AIR BLEEDING OF CONTROL VALVE . >

  21. Check the level and leaks of the ATF.

    <Ref. to AUTOMATIC TRANSMISSION FLUID . >

· About lemon-mirror