lemon-mirror:
Home >> Subaru >> 2013 >> Outback Base, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 17 (Automatic Transaxle) >> Front Vehicle Speed Sensor >> Installation

Front Vehicle Speed Sensor: Installation

WARNING: This page is about a different car, the 2013 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
  1. Pass the transmission harness assembly through the hole of the transmission case.
    NOTE: Use new O-rings.
    Fig 1: Identifying Transmission Harness Assembly
    G05002532Courtesy of SUBARU OF AMERICA, INC.
  2. Connect the control valve connector and transmission ground.

    Tightening torque: 

    8 N.m (0.8 kgf-m, 5.9 ft-lb) 

    Fig 2: Identifying Control Valve Connector And Transmission Ground
    G08563949Courtesy of SUBARU OF AMERICA, INC.
  3. Apply proper amount of liquid gasket to the entire oil pan mating surface.

    Liquid gasket: 

    THREE BOND 1217B (Part No. K0877YA020) or equivalent 

    Fig 3: Identifying Liquid Gasket Applying Area On Oil Pan Mating Surface
    G05002534Courtesy of SUBARU OF AMERICA, INC.
  4. Fill the 3 locations of the transmission case excluding the bolt holes with an ample amount of liquid gasket.

    Liquid gasket: 

    THREE BOND 1217B (Part No. K0877YA020) or equivalent 

    Fig 4: Locating Oil Pan Mounting Bolts
    G08563951Courtesy of SUBARU OF AMERICA, INC.
  5. Install the oil pan by equally tightening the bolts.

    Tightening torque: 

    5 N.m (0.5 kgf-m, 3.7 ft-lb) 

  6. Install the front vehicle speed sensor and torque converter turbine speed sensor.
    NOTE: Use new O-rings.

    Tightening torque: 

    7 N.m (0.7 kgf-m, 5.2 ft-lb) 

  7. Install the ATF cooler inlet and outlet pipes.
    NOTE: Use a new copper washer.

    Tightening torque: 

    T1: 25 N.m (2.5 kgf-m, 18.4 ft-lb) 

    T2: 40 N.m (4.1 kgf-m, 29.5 ft-lb) 

    T3: 45 N.m (4.6 kgf-m, 33.2 ft-lb) 

    Fig 5: ATF Cooler Inlet And Outlet Pipes With Torque Specifications
    G05956005Courtesy of SUBARU OF AMERICA, INC.
  8. Install the transmission rear crossmember bolt.

    Tightening torque: 

    70 N.m (7.1 kgf-m, 51.6 ft-lb) 

  9. Install the propeller shaft. < Refer to INSTALLATION , Propeller Shaft. >
  10. Install the heat shield cover. < Refer to INSTALLATION , Heat Shield Cover. >
  11. Install the center exhaust pipe. (non-turbo model) < Refer to INSTALLATION , Center Exhaust Pipe. >
  12. Install the center exhaust pipe. (turbo model) < Refer to INSTALLATION , Center Exhaust Pipe. >
  13. Lower the vehicle.
  14. Install the transmission harness connector to the stay.
  15. Install the pitching stopper. < Refer to INSTALLATION , Transmission Mounting System. >
  16. Install the air intake boot assembly. (non-turbo model) < Refer to INSTALLATION , Air Intake Boot. >
  17. Install the intercooler. (turbo model) < Refer to INSTALLATION , Intercooler. >
  18. Connect the battery ground terminal.
  19. Fill with the same amount of ATF as drained. < Refer to INSPECTION , Automatic Transmission Fluid. >
  20. Bleed the air of control valve. < Refer to PROCEDURE , Air Bleeding of Control Valve. >
  21. Inspect the level of ATF. < Refer to INSPECTION , Automatic Transmission Fluid. >
  22. Perform the diagnosis again. < Refer to PROCEDURE , Learning Control. >
· About lemon-mirror