lemon-mirror:
Home >> Toyota >> 2012 >> Yaris SE, Automatic Trans >> Repair and Diagnosis >> General Information >> Identification >> Introduction >> REPAIR INSTRUCTION (for Hatchback) >> Initialization >> Initialization

REPAIR INSTRUCTION (for Hatchback): Initialization: Initialization

  1. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED 
    PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

    Replacement Part Necessary Procedure Effect or Inoperative Function when Necessary Procedure is not Performed See
    ECM Vehicle Identification Number (VIN) registration DTC P0630 is output Refer to REGISTRATION
    ECU communication ID registration
    (Engine immobilizer system)    		 Engine starting Refer to REGISTRATION
    • Throttle with motor body assembly
    • Engine assembly
    • Cylinder head
    • Camshaft (for intake side)
    • Camshaft timing gear assembly
    • Piston or piston ring
    • Mass air flow meter
    • Fuel injector assembly
    • Fuel pump
    • Air fuel ratio sensor
    • Engine coolant temperature sensor
    • Spark plug
    • No. 1 ignition coil
    • EGR valve assembly
    • Knock sensor
    		 Inspection after repairs - Refer to INITIALIZATION
    Automatic transaxle assembly, engine assembly or ECM
    • Road test
    • Reset memory
    		 Large shift shock Refer to INITIALIZATION
    • Door control and tire pressure monitoring system receiver assembly*1
    • Tire pressure monitor receiver assembly*2
    		 Register transmitter IDs
    • When DTC detection conditions of "transmitter ID not received" DTC is met, tire pressure warning light blinks for 1 minute, and then illuminates
    • Tire pressure monitoring function
    		 Refer to INITIALIZATION for Initialization
    Refer to REGISTRATION for Registration
    Tire pressure warning valve and transmitter Refer to REGISTRATION
    Yaw rate and deceleration sensor (Airbag sensor assembly)*3
    • Clearing zero point calibration data
    • Yaw rate and deceleration sensor zero point calibration
    		 VSC control is prohibited or operation is incorrect Refer to CALIBRATION
    Yaw rate and deceleration sensor (Yaw rate sensor)*4 Refer to CALIBRATION
    Skid control ECU
    (Brake actuator assembly)    		 Yaw rate and acceleration sensor zero point calibration VSC control is prohibited or operation is incorrect Refer to CALIBRATION
    Front wheel alignment
    • Clearing zero point calibration data
    • Yaw rate and acceleration sensor zero point calibration
    		 VSC control is prohibited or operation is incorrect Refer to CALIBRATION
    • Power steering ECU
    • Power steering column sub-assembly
    • Power steering motor
    • Steering wheel
    • Steering gear assembly
    		 Perform rotation angle sensor initialization and torque sensor zero point calibration
    • Power steering warning light comes on
    • EPS control
    		 Refer to CALIBRATION
    • Door control and tire pressure monitoring system receiver assembly*5
    • Door control receiver*6
    • Key
    		 Code registration Wireless door lock system Refer to REGISTRATION
    • Transponder key ECU
    • Key
    • ECM
    		 ECU communication ID registration
    (Engine immobilizer system)    		 Engine start Refer to REGISTRATION
    • Occupant classification ECU
    • Accessories (seatback tray and seat cover, etc.) are installed
    • Front passenger seat is removed from the vehicle
    • Vehicle is brought to the workshop for repair due to an accident or a collision
    • Perform zero point calibration
    • Sensitivity check
    • Occupant classification system
    • Airbag system (Front passenger side)
    • Seat belt warning system (Front passenger side)
    		 Refer to INITIALIZATION
    • *1: w/ Wireless Door Lock Control System
    • *2: w/o Wireless Door Lock Control System
    • *3: for Hatchback with Built-in Type Yaw Rate Sensor
    • *4: for Hatchback with Separate Type Yaw Rate Sensor
    • *5: w/ Tire Pressure Warning System
    • *6: w/o Tire Pressure Warning System
· About lemon-mirror