Transmission Cable, Control Module - Removal & Installation
- Transmission
- Remove transmission cable from bracket and from lever on transmission
- Install transmission cable on transmission
- Transmission checking/fault-tracing
- Transmission control module (TCM), replacing (B5254T4, TF-80SC AWD; 2006-2007) (version 1)
- Transmission control module (TCM), replacing (B5254T4, TF-80SC AWD; 2006-2007) (version 2)
- Transmission fluid, changing (TF-80SC AWD; 2006-2007)
- Transmission fluid, replacing (AW50/51 AWD; W55-50/51SN; 2003-2009)
- Transmission replacement, post-checking
- Transmission, installing (AW50/51 AWD; W55-50/51SN; 2003-2009)
- Transmission, installing (D5252T diesel engine)
- Notes
- Checking before installing
- Adjusting the position of the engine and transmission
- Installing and tightening the screws for the transmission
- Installing the dip stick pipe and oil hose on the oil cooler. Install the 3 screws for the transmission
- Installing the torque converter screws
- Installing the collision protection system over the steering gear (right-hand drive cars)
- Installing components on the sub-frame
- Lifting the engine and transmission to the horizontal position
- Installing the rear engine mounting
- Installing the sub-frame on the bodywork
- Installing the left drive shaft on the transmission, wheel spindle and control arm
- Installing the engine stabilizer brace
- Installing the exhaust pipe on the turbocharger (TC) and the starter motor on the engine
- Installing the right drive shaft on the transmission, wheel spindle and control arm
- Installing and tightening the sub-frame screws
- Installing and tightening front end components (both sides)
- Tightening the ball joint pinion
- Installing a new screw and new lock nuts for the steering gear
- Removing the tie strap from the steering gear
- Installing and tightening the screw for the rear engine pad
- Installing the delivery line on the rubber hoses
- Installing the front cross member
- Installing the screw for the ground lead and cable conduit
- Lowering the car and removing the lifting beam and lifting tools from the engine
- Installing the remaining screws for the transmission and starter motor
- Installing the torque control arm
- Installing the transmission cable bracket on the transmission and the cable on the lever
- Installing the air hose on the turbocharger (TC) and the delivery line on the manifold
- Installing the upper torque rod in the engine compartment
- Installing the air cleaner (ACL) housing and engine cover
- Checking the transmission fluid level
- Transmission, installing (AW55-50/51SN; 2004-2007)
- Notes
- Installing the transmission
- Adjusting the position of the engine and transmission
- Installing and tightening the screws for the transmission
- Installing the torque converter screws
- Lifting the engine and transmission to the horizontal position
- Installing the rear engine mounting
- Installing the lower oil pipe on the transmission
- Installing the bevel gear
- Installing the left drive shaft on the transmission and the wheel spindle
- Installing the subframe on the bodywork
- Installing the right drive shaft on the transmission, wheel spindle and control arm
- Tightening the subframe screws (both sides)
- Fitting the screws for engine pads and the torque rod bracket in the gearbox
- Installing the steering wheel shaft joint
- Installing the collision protection system over the steering gear
- Installing the cross member
- Installing and tightening the front suspension components
- Installing the wiring duct
- Removing the lifting beam
- Installing the remaining screws for the transmission and starter motor
- Installing the exhaust gas recirculation (EGR) cooler
- Installing the vacuum pump
- Installing the gear selector cable and oil pipe
- Installing service clips
- Installing engine compartment components
- Finishing
- Transmission, installing (AW50AWD)
- Notes
- Installation
- Notes
- Installing the transmission
- Installing and tightening the screws for the transmission
- Installing the torque converter screws
- Lifting the engine and transmission
- Installing the rear engine mounting
- Installing the bevel gear
- Installing the lower oil pipe on the transmission
- Installing the left drive shaft on the transmission and the wheel spindle
- Installing the sub-frame on the bodywork
- Installing the right-hand drive shaft on the transmission, wheel spindle and control arm
- Installing components on the engine and sub-frame
- Installing the collision protection system over the steering gear
- Checking the position of the tie rod in the steering gear
- Assembling the lower steering shaft
- Installing the cross members on the body
- Installing front suspension components
- Installing components for the fender liner
- Installing the cable duct
- Installing the front splash guard
- Removing the lifting beams
- Installing the coolant hose
- Installing the remaining screws for the transmission and starter motor
- Installing the gear selector cable and oil pipe
- Installing the service clips
- Installing engine compartment components
- Installing the battery lead
- Finishing
- Transmission, installing (M66 AWD; 2004-2007)
- Notes
- Installation
- Notes
- Installing the transmission
- Installing and tightening screws for the transmission
- Lifting the engine and transmission to the horizontal position
- Installing the rear engine mounting
- Installing the bevel gear
- Installing the lower charge air pipe
- Installing the left drive shaft on the transmission and the wheel spindle
- Fitting the sub-frame to the body
- Installing the right-hand drive shaft to the gearbox, wheel spindle and link arm
- Positioning the mobile jack under the right-hand side of the sub-frame
- Fitting the screws for engine pads and the torque rod bracket in the gearbox
- Installing the steering wheel shaft joint
- Installing the collision protection system over the steering gear
- Installing the crossmembers
- Installing and tightening front suspension components
- Installing the cable duct
- Removing the lifting beams
- Installing the screws in the transmission / engine
- Installing the lever and transmission cables
- Installing the service clips
- Installing the hose nipple on the junction for the clutch bearing
- Installing engine compartment components
- Transmission cable, adjusting
- Finishing