Chassis Electrical
- Battery
- Ignition Switch
- General Description
- Ignition Key Reminder Tone Alarm And Door Lock Prevention Function Diagnosis
- Encrypted Code Registration Criteria Table
- Immobilizer System Diagnosis
- Introduction To Immobilizer System Diagnosis
- Immobilizer System Diagnostic Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- Symptom Chart
- Symptom Procedures
- Data List Reference Table
- Check At ETACS-Ecu (Immobilizer-Ecu) Terminal
- Special Tools
- On-Vehicle Service
- Ignition Switch
- ETACS-Ecu
- Combination Meter Assembly
- General Description
- Combination Meters Diagnosis
- Troubleshooting Strategy
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC B1200: Defective odometer
- DTC B1201: Defective fuel gauge
- DTC U1073: Bus Off
- DTC U1100: Powertrain Control Module Time-out (Related to Engine); DTC U1101: Powertrain Control Module Time-out (Related to A/T)
- DTC U1102: ABS-ECU Time-out
- DTC U1109: ETACS-ECU Time-out
- DTC U1112: SRS-ECU Time-out
- DTC U1120: Failure Information on Powertrain Control Module (Related to Engine)
- DTC U1206: Flag invalid
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication with Scan Tool is Not Possible
- INSPECTION PROCEDURE 2: Power Supply Circuit.; INSPECTION PROCEDURE 3: Odometer and Trip Meter are not Displayed.; INSPECTION PROCEDURE 4: All the Needle Meters do not Work.; INSPECTION PROCEDURE 5: When the Ignition Switch is Turned to the ON Position, the Indicator and Warning Lights do not Illuminate
- INSPECTION PROCEDURE 6: Speedometer does not Work.; INSPECTION PROCEDURE 7: The Fuel Gauge Needle Moves Excessively
- INSPECTION PROCEDURE 8: Tachometer does not Work
- INSPECTION PROCEDURE 9: Fuel Gauge does not work (other meters work)
- INSPECTION PROCEDURE 10: Engine Coolant Temperature Gauge does not Work (other meters work)
- Data List Reference Table
- Actuator Test Reference Table
- Combination Meter Terminal Check
- Special Tools
- On-Vehicle Service
- Combination Meter Assembly
- Headlight, Front Side Marker Light And Position Light Assembly
- Fog Light
- Rear Combination Light
- Dome Light
- Rheostat
- Hazard Warning Light Switch
- Column Switch
- Horn
- Accessory Socket
- Radio With Cd Player
- General Description
- Radio With Cd Player, Speaker And Antenna Diagnosis
- Introduction To Audio System Diagnosis
- Audio System Diagnostic Troubleshooting Strategy
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: When Power Switch is Turned "ON," no Power is Available
- INSPECTION PROCEDURE 2: When Remote Controlled Radio Power Switch is Turned "ON," no Power is Available. But Radio, CD Player and CD Changer Power Switch is Available. < Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 3: The System does not Recognize the Remote Controlled Radio Switch (RH) Only. < Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 4: The System does not Recognize the Remote Controlled Radio Switch (LH) Only.< Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 5: No Sound. < Vehicles with Audio Amplifier >
- INSPECTION PROCEDURE 6: No Sound from One Speaker. < Vehicles without audio amplifier >
- INSPECTION PROCEDURE 7: No Sound from One Speaker. < Vehicles with audio amplifier >
- INSPECTION PROCEDURE 8: Noise is Present while Moving (AM)
- INSPECTION PROCEDURE 9: Noise is Present while Moving (FM)
- INSPECTION PROCEDURE 10: Sound mixed with Noise, Only at Night (AM)
- INSPECTION PROCEDURE 11: Noise is Overpowering both AM and FM
- INSPECTION PROCEDURE 12: Excessive Noise on AM and FM
- INSPECTION PROCEDURE 13: Noise is Detected with Engine Running
- INSPECTION PROCEDURE 14: Noise Appears During Vibration or Shocks
- INSPECTION PROCEDURE 15: Noise is Present While Moving (FM)
- INSPECTION PROCEDURE 16: Constant Noise
- INSPECTION PROCEDURE 17: No Reception (AM)
- INSPECTION PROCEDURE 18: Poor Reception
- INSPECTION PROCEDURE 19: Distortion on AM and/or FM
- INSPECTION PROCEDURE 20: Distortion on FM Only
- INSPECTION PROCEDURE 21: Auto Select Function Inoperative, too Few Automatic Stations are Selected
- INSPECTION PROCEDURE 22: Preset Stations are Erased
- INSPECTION PROCEDURE 23: CD can not be Inserted
- INSPECTION PROCEDURE 24: No Sound (CD Only)
- INSPECTION PROCEDURE 25: CD Sound Skips
- INSPECTION PROCEDURE 26: Sound Quality is Poor
- INSPECTION PROCEDURE 27: CD cannot be Ejected
- INSPECTION PROCEDURE 28: Only the satellite radio cannot be heard normally
- On-Vehicle Service
- Special Tool
- Remote Controlled Radio Switch
- Amplifier
- Antenna < Vehicles Without Satellite Radio Tuner >
- Defogger
- Multi-Center Display
- General Description
- Notes
- Character Display Function Of Low Grade Multi-Center Display
- Graphical Display Function Of Middle Grade Multi-Center Display
- Precautions During Service
- Communication Error Processing < Middle Grade Type >
- Failure Diagnosis Service Mode Function < Middle Grade Type >
- Fail-Safe Function Of The Multi-Center Display Unit (Middle Grade Type)
- Diagnosis Function
- Diagnostic Trouble Code Chart
- Diagnostic Trouble Code Procedures
- DTC 010: Buss Off
- DTC 011: Powertrain Control Module Time-out (Related to Engine); DTC 012: Powertrain Control Module Time-out (Related to A/T)
- DTC 013: A/C-ECU Time-out
- DTC 014: Combination Meter Time-out
- DTC 019: ETACS-ECU Time-out
- DTC 020: Failures Information on Powertrain Control Module (Related to Engine)
- DTC 021: Failures Information on Combination Meter
- DTC 022: Failures Information on A/C-ECU
- Diagnosis
- Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication With Scan Tool Is Not Possible. (Middle Grade Type)
- INSPECTION PROCEDURE 2: The Multi-center Display does not Show any Information. (Middle Grade Type)
- INSPECTION PROCEDURE 3: The A/C Display Shows "COMMUNICATION ERROR", and then can not Proceed to Next Screen. (Middle Grade Type or Vehicles With Mitsubishi Multi Communication system)
- INSPECTION PROCEDURE 4: The Ambient Air Temperature Display Shows "COM ERROR" or "--°C (--°F)." (Middle Grade Type or Vehicles With Mitsubishi Multi Communication system)
- INSPECTION PROCEDURE 5: On the Audio Screen, "COMMUNICATION ERROR" can not Proceed to Next Screen. (Middle Grade Type)
- INSPECTION PROCEDURE 6: The Compass can not be Calibrated Manually, or Becomes Out of Calibration Easily (Middle Grade Type)
- On-Vehicle Service
- Special Tools
- General Description
- MMCS
- Special Tools
- Troubleshooting
- Precautions During MMCS Service
- Diagnosis Service Function
- Diagnostic Trouble Code Chart
- Trouble Symptom Chart
- Symptom Procedures
- INSPECTION PROCEDURE 1: Communication between M.U.T.-III and multi-center display is not possible
- INSPECTION PROCEDURE 2: The screen is not displayed with ACC-ON
- INSPECTION PROCEDURE 3: Check the power supply circuit system of multi-center display
- INSPECTION PROCEDURE 4: The daytime/nighttime display mode on multi-center display does not switch
- INSPECTION PROCEDURE 5: The multi-center display operation tone (beep sound) does not sound
- INSPECTION PROCEDURE 6: The audio communication error screen is displayed to the multi-center display
- INSPECTION PROCEDURE 7: The navigation screen is not displayed at all
- INSPECTION PROCEDURE 8: The navigation display screen runs or the screen color tone is considerably unnatural
- INSPECTION PROCEDURE 9: The navigation sound is not output or the noise enters in the sound
- INSPECTION PROCEDURE 10: The touch panel operation is ineffective
- INSPECTION PROCEDURE 11: The menu operation is possible even during driving. /The current position display (vehicle mark) does not move. (The mark sometimes moves by leaping.)
- INSPECTION PROCEDURE 12: The vehicle position is not displayed normally/The vehicle position does not move forward inside a tunnel
- INSPECTION PROCEDURE 13: The navigation returns to the opening screen
- INSPECTION PROCEDURE 14: The map disc is not read
- INSPECTION PROCEDURE 15: The map disc cannot be inserted
- INSPECTION PROCEDURE 16: GPS cannot be received
- INSPECTION PROCEDURE 17: When in the navigation mode, the messages below are displayed
- INSPECTION PROCEDURE 18: The current position display (vehicle mark) only moves forward or backward
- INSPECTION PROCEDURE 19: Even when the vehicle turns the traffic intersection, the current position display (vehicle position) does not make a turn
- INSPECTION PROCEDURE 20: Only the front left speaker does not sound (including the audio sound)
- Main Unit Terminal Voltage
- Ambient Temperature Sensor
- Theft Alarm
- Specifications